1. Air intrusion. When the air intrudes into the hydraulic system, it has a large volume in the low-pressure area. When it enters the high-pressure area, it is compressed, and the volume suddenly decreases. When it enters the low-pressure area, the volume suddenly increases, resulting in a sudden change in the bubble volume, that is, "explosion" phenomenon, resulting in noise. Solution: Generally, the hydraulic cylinder is equipped with an exhaust device want to buy Low speed high torque cycloidal hydraulic motor Exhaust. In addition, a common method is to exhaust the actuator several times during the fast full stroke after startup. 2. The quality of the hydraulic pump or motor is poor. The quality of the hydraulic pump is poor, the accuracy does not fully meet the technical requirements, the pressure and flow fluctuations are large, the oil trapping phenomenon has not been eliminated well, and poor sealing and poor bearing quality are the main reasons for the noise. In use, due to wear of hydraulic pump parts, excessive clearance, insufficient flow Qinghai Manufacturer The force is easy to fluctuate and will also produce noise.
As a kind of hydraulic transmission device, hydraulic motor has been widely used in many places. In fact, I have seen it on many occasions. The main application fields are. 1. The hydraulic motor has convenient speed regulation, which can be adjusted infinitely from 0 to the maximum speed according to the adjustment of the hydraulic valve. The motor itself does not need special design and has low cost. This is much cheaper than motor+reducer, or variable frequency motor and servo motor. 2. The hydraulic system has strong anti overload capacity and relies on the overflow valve for protection, allowing a long time want to buy Low speed high torque cycloidal hydraulic motor (Relatively) Frequent overload, easy to recover under overload, no damage to equipment, no restart of equipment. 3. The hydraulic system is characterized by high energy density. For motors of the same power, hydraulic motors are much smaller than motors Low speed high torque cycloidal hydraulic motor Manufacturer , much lighter. And it is easy to apply to mobile devices. 4. The hydraulic motor is totally enclosed and can be safely used in dusty, wet (even underwater) and flammable environments, which is much more reliable than explosion-proof (flameproof) motors.
Hydraulic transmission system, the hydraulic transmission system is generally an open loop system without feedback, which mainly transmits power, supplemented by information, and pursues the perfection of transmission characteristics. Hydraulic elements want to buy Low speed high torque cycloidal hydraulic motor The characteristics of components and their interactions determine the working characteristics of the system, and its working quality is greatly affected by the changes of working conditions. Hydraulic drive system is widely used. The hydraulic system of most industrial equipment belongs to this category. In the hydraulic control system, servo valves and other electrohydraulic devices are mostly used in the hydraulic control system Low speed high torque cycloidal hydraulic motor Manufacturer The control valve constitutes a closed-loop system with feedback, which mainly transmits information, supplemented by power, and pursues the perfection of control performance. The system adds detection feedback, which can combine common components into an accurate control system, and its control quality is less affected by the change of working conditions. Hydraulic control system is widely used in high-precision CNC machine tools, metallurgy, aerospace and other industries.
(1) Oil leakage at the shaft end: because the oil seal and output shaft are under constant friction during the use of the hydraulic motor, the wear of the contact surface between the oil seal and the shaft will be caused Qinghai Low speed high torque cycloidal hydraulic motor A certain limit will make the oil seal lose its sealing effect, and oil will leak. Our solution is very simple: replace the oil seal. If the output shaft is seriously worn, it must be replaced. (2) Crevice oil leakage: the "O" ring between the motor housing and the front side plate, or between the front side plate and the stator body, is aged Low speed high torque cycloidal hydraulic motor Manufacturer Just replace the "O" ring. (3) Oil leakage at the cover: the "O" ring under the cover is aged and loses its sealing effect. The probability of this situation is very low, even if it happens, just replace the "O" ring.
During the operation of hydraulic transmission, the hydraulic actuator can be adjusted steplessly in a large range by adjusting the control valve, and the speed range can reach 2000 meters. Good operation ability and rapidity. The liquid is elastic and can absorb impact, so the hydraulic transmission movement is even and stable; It is easy to realize fast starting, braking and frequent reversing. Reciprocating rotation want to buy Low speed high torque cycloidal hydraulic motor The reversing frequency of rotary motion can reach 500 times/minute, and the reciprocating linear motion can reach 1000 times/minute. It is easy to control operation and realize overload protection. The hydraulic system with convenient operation and control is convenient for automatic control, remote control and overload protection; Automatic lubrication during operation, which is beneficial to Qinghai Manufacturer Heat dissipation, prolong service life. It is convenient for automation and electromechanical hydraulic integration. Hydraulic technology is easy to combine with electric control and electric control technology to form an electromechanical hydraulic integration composite system to realize automatic cycle work.
