Precautions during operation of cycloidal hydraulic motor: before operation, check whether all parts of the hydraulic system are connected correctly, and inject oil into the specified Qinghai Cycloidal motor of overhead crane Height. Start and run without load for 10-15 minutes, and exhaust. Air bubbles in the oil tank, noise in the system, and gas accumulation in the engine oil cylinder all prove that there is air in the system. After the gas is discharged, fill the oil tank, and then gradually increase the load of the motor until the load is too large. Observe whether there is noise, oil rise, oil leakage and other abnormal phenomena. After 50 hours of operation, change the oil according to the maintenance rules, and then the oil according to the maintenance rules Qinghai manufactor Replace. If there is no motor fault, do not disassemble it easily.

If the hydraulic system is compared to the human body, then the hydraulic oil is equal to human blood. In the hydraulic system, the hydraulic oil plays a role in energy transmission, system lubrication, and prevention Qinghai Cycloidal motor of overhead crane The functions of corrosion, rust prevention and cooling, and whether the hydraulic system can work effectively are closely related to the type and selection of hydraulic oil. Coding, composition and characteristics of hydraulic system: high purity general machine tool oil, refined mineral lubricating oil, with good rust resistance and oxidation resistance. High wear resistant hydraulic oil, refined mineral lubricating oil, rust proof, anti-oxidation, anti-wear. High temperature and high pressure hydraulic oil, with the characteristics of rust prevention, oxidation resistance, wear resistance, etc., is refined into mining lubricating oil, and added with viscosifier. Refined mining lubricating oil HG hydraulic guide oil, rust proof, anti-oxidation, anti-wear, anti stick slip. HS synthesis customized Cycloidal motor of overhead crane Hydrocarbon is a kind of low temperature hydraulic oil, which has the characteristics of anti-oxidation and anti-wear.

When the working load changes from low speed to high speed in a wide range, the hydraulic motor is also required to be able to drive and regulate speed in the corresponding wide range, which requires the motor to have good low-speed stability and high speed performance. The speed regulation range K of the hydraulic motor is usually expressed by the ratio of the allowable maximum speed to the minimum speed. customized Cycloidal motor of overhead crane It is the highest operating speed of hydraulic motor, but it is limited by many factors, mainly including: 1. Service life. After the speed increases, each pair is worn Qinghai manufactor The service life is shortened. 2、 Mechanical efficiency limits. At high speed, the hydraulic motor needs to input large flow, accordingly, the hydraulic loss of each circulating component increases, reducing the mechanical efficiency.

(1) Oil leakage at the shaft end: because the oil seal and output shaft are under constant friction during the use of the hydraulic motor, the wear of the contact surface between the oil seal and the shaft will be caused Qinghai Cycloidal motor of overhead crane A certain limit will make the oil seal lose its sealing effect, and oil will leak. Our solution is very simple: replace the oil seal. If the output shaft is seriously worn, it must be replaced. (2) Crevice oil leakage: the "O" ring between the motor housing and the front side plate, or between the front side plate and the stator body, is aged Cycloidal motor of overhead crane manufactor Just replace the "O" ring. (3) Oil leakage at the cover: the "O" ring under the cover is aged and loses its sealing effect. The probability of this situation is very low, even if it happens, just replace the "O" ring.

In the late 1850s, the original low-speed high torque hydraulic motor was developed from the fixed rotor part of the oil pump, which consists of an internal gear ring and matching teeth Qinghai manufactor Wheel or rotor. The inner gear ring is fixedly connected with the housing, and the oil entering from the oil port pushes the rotor to rotate around the center point. This slowly rotating rotor is driven and output by a spline shaft to become a cycloidal hydraulic motor. After the first cycloid motor came out, after decades of evolution, Jinjia hydraulic hydraulic motor delivers high efficiency energy for you. Another concept of motor also began to form. The motor installs the drum in the built-in ring gear. Motors with rollers can provide high starting Cycloidal motor of overhead crane manufactor With the running torque, the drum reduces friction and improves efficiency. The low speed output shaft can also produce stable output.

BM cycloidal hydraulic motor is a small low-speed high torque hydraulic motor with single axis flow distribution and fixed rotor set. Its advantages are as follows: 1. It is small in size and light in weight, and its overall size is much smaller than other types of hydraulic motors with the same torque. 2. Wide speed range, stepless speed regulation, minimum stable speed up to 15 rpm, convenient installation and layout, low investment cost. 3. It can be used in series or parallel in the hydraulic system. 4. The moment of inertia is small, and it is easy to start under load. It can rotate in both forward and reverse directions, and it does not need to stop when reversing. BM cycloidal motor is widely used in agriculture, fishery, light industry Cycloidal motor of overhead crane manufactor The slewing mechanism of hoisting and transportation, mining, construction machinery and other machinery. Examples of BM cycloidal hydraulic motor used abroad; 1) Agricultural use: various combine harvesters, seeders, rotary tillers, lawn mowers, sprayers, feed mixers, ground drills. 2) Fishery use: net lifter. customized Cycloidal motor of overhead crane 3) Light industry: commercial winding machines, textile machines, printing machines, washing machines. 4) For construction industry: road roller, cement mixer, sweeper.